-
Scott Davis started the topic Loss to the 6×6 Community in the forum Everything Else 1 year, 7 months ago
A long-time member of the 6×6 community Dave Glogowski (Little G) lost his partner of over 20 years, Terri Hall, earlier in the month. He has many costs including funeral and medical so there is a GoFundMe to help him with some of those costs. Dave’s family has been involved with 6-wheelers since the beginning. He is the rep for the 6×6 racers i…[Read more]
-
Rod posted an update 1 year, 7 months ago
Happy Birthday Andrew
-
Allen Davis became a registered member 1 year, 7 months ago
-
Wilfred Hass became a registered member 1 year, 7 months ago
-
Cody McCollum changed their profile picture 1 year, 8 months ago
-
Cody McCollum posted an update 1 year, 8 months ago
The best ATV ever made!!
-
Cody McCollum became a registered member 1 year, 8 months ago
-
Patrick F Kent became a registered member 1 year, 8 months ago
-
Rod and TJ Startt are now friends 1 year, 8 months ago
-
Rod became a registered member 1 year, 8 months ago
-
Douglas became a registered member 1 year, 8 months ago
-
Tom became a registered member 1 year, 9 months ago
-
Gene Boyd changed their profile picture 1 year, 9 months ago
-
Gene Boyd commented on Andrew‘s photo gallery 1 year, 9 months ago
Nice, I was wanting to know what is the width of the springer? I’m thinking of building one.
-
It’s 72″ or 73″ if I remember. It’s been a while since I measured it. We do plan on offering new MAX Springers once the MAX production line is open.
-
I’m interested in a springer. I posted some pictures of what I’ve done using parts from an Arctic Cat 4 wheeler. But the wheel width is about 81 inches, Which I think is too wide.
-
-
-
Donsld Ferguson Jr started the topic Input shaft too short, clutch wobbles to death in the forum T-20 Transmission 1 year, 9 months ago
Hello. My first entry here. I have major issues with the secondary cluch bolt rattling loose and causing the clutch to wobble, which enlargens the center hole. This enlargened hole ruins the clutch, as it don’t fit the input shaft snug any more.
The bolt is new, lots of high strength loktite used, new lock washer. Yet, it eventually wobbles…[Read more]
-
Sounds like you got something else going on .I have never seen or heard of a secondary coming loose in one of these.In 45 years i never needed to loctite a bolt on usually the problem is you can’t get the clutch off are you sure your not missing the key way and the clutch is spinning on the shaft and loosening up.I saw someone ride an entire…[Read more]
-
Thank you. There must be something else going on that I can’t figure out.
Yes, the proper key is installed. The clutch is new, the T20 works fine.
I don’t have the length of the original bolt installed at the factory . It broke many years ago and I replaced it with one “close enough” because its all the hardware store had in stock. It is 4 inches…[Read more] -
Once the secondary clutch is installed on the input shaft I see a long space from the tip of the shaft to the “mouth” of the clutch hole. Is there supposed to be a filler block in there, or is this just empty space? Thanks.
-
Its just empty space but they did use a real thick washer on the end so you could crank the bolt tight.
-
Thank you. It does have the thick washer.
I think the problem this time is the new bolt I used was a tad too long and bottomed out just as itvwas getting tight.
That was my gut feeling when I tightened it, thatvit may have ottomedcout, and it seemed to very tight. The clutch was on tight.
What makes me think this is the case is the bolt did not…[Read more]
-
-
-
-
-
Andrew posted an update 1 year, 9 months ago
We are excited to announce we have new bearing cages in stock at http://www.maxatvs.com! Regular cages are $59.98 each, and Front cages with Plow Mounts are $159.96 for a set of two.
-
Brad became a registered member 1 year, 9 months ago
-
Michael Laughlin became a registered member 1 year, 9 months ago
-
Andrew and TJ Startt are now friends 1 year, 9 months ago
-
Andrew and Cory are now friends 1 year, 9 months ago
- Load More